MN101C67D, mn101c67g ram ( 8-bit) rom ( 8-bit) type minimum instruction execution time standard: 0.1 s (at 2.5 v to 3.6 v, 20 mhz)* 0.2 s (at 2.1 v to 3.6 v, 10 mhz)* 0.5 s (at 1.8 v to 3.6 v, 4 mhz)* 62.5 s (at 1.8 v to 3.6 v, 32 khz)* double speed: 0.119 s (at 2.5 v to 3.6 v, 8.39 mhz)* * the operation guarantee range for flash memory built-in type is 3.0 v to 3.6 v. interrupts ? reset watchdog external 0 external 1 external 2 external 3 external 4 external 5 timer 0 timer 1 timer 2 timer 3 timer 4 timer 5 timer 6 time base serial 0 reception serial 0 transmission serial 1 reception serial 1 transmission serial 2 serial 3 serial 4 automatic transfer finish a/d conver sion finish timer 7 (2 systems) key interrupts (8 lines) timer counter timer counter 0 : 8-bit 1 (square-wave/8-bit pwm output, event count, generation of remote control carrier, pulse width measurement) clock source 1/2, 1/4 of system clock frequency; 1/1, 1/4, 1/16, 1/32, 1/64 of osc oscillation clock frequency; 1/1 of xi oscillation clock frequency; external clock input interrupt source coincidence with compare register 0 timer counter 1 : 8-bit 1 (square-wave output, event count, synchronous output event) clock source 1/2, 1/8 of system clock frequency; 1/1, 1/4, 1/16, 1/64, 1/128 of osc oscillation clock frequency; 1/1 of xi oscillation clock frequency; external clock input interrupt source coincidence with compare register 1 timer counter 0, 1 can be cascade-connected. timer counter 2 : 8-bit 1 (square-wave/8-bit pwm output, event count, synchronous output event, pulse width measurement) clock source 1/2, 1/4 of system clock frequency; 1/1, 1/4, 1/16, 1/32, 1/64 of osc oscillation clock frequency; 1/1 of xi oscillation clock frequency; external clock input interrupt source coincidence with compare register 2 timer counter 3 : 8-bit 1 (square-wave output, event count, generation of remote control carrier) clock source 1/2, 1/8 of system clock frequency; 1/1, 1/4, 1/16, 1/64, 1/128 of osc oscillation clock frequency; 1/1 of xi oscillation clock frequency; external clock input interrupt source coincidence with compare register 3 timer counter 2, 3 can be cascade-connected. timer counter 4 : 8-bit 1 (square-wave/8-bit pwm output, event count, pulse width measurement, serial 1 baud rate timer) clock source 1/2, 1/4 of system clock frequency; 1/1, 1/4, 1/16, 1/32, 1/64 of osc oscillation clock frequency; 1/1 of xi oscillation clock frequency; 1/1 of external clock input frequency interrupt source coincidence with compare register 4 timer counter 5 : 8-bit 1 (square-wave/8-bit pwm output, event count, pulse width measurement, serial 0 baud rate timer) clock source 1/2, 1/4 of system clock frequency; 1/1, 1/4, 1/16, 1/32, 1/64 of osc oscillation clock frequency; 1/1 of xi oscillation clock frequency; 1/1 of external clock input frequency interrupt source coincidence with compare register 5 package tqfp080-p-1212d *lead-free 64 k 6 k MN101C67D (under development) mad00036eem mn101c67g 128 k 10 k
MN101C67D, mn101c67g timer counter (continue) timer counter 6 : 8-bit freerun timer clock source 1/1 of system clock frequency; 1/1, 1/4096, 1/8192 of osc oscillation clock frequency; 1/1, 1/4096, 1/8192 of xi oscillation clock frequency interrupt source coincidence with compare register 6 timer counter 7 : 16-bit 1 (square-wave/16-bit pwm output, cycle / duty continuous variable, event count, synchronous output evevt, pulse width measurement, input capture) clock source 1/1, 1/2, 1/4, 1/16 of system clock fr equency; 1/1, 1/2, 1/4, 1/16 of osc oscillation clock frequency; 1/1, 1/2, 1/4, 1/16 of external clock input frequency interrupt source coincidence with compare register 7 (2 lines) time base timer (one-minute count setting) clock source 1/1 of osc oscillation clock frequency; 1/1 of xi oscillation clock frequency interrupt source 1/128, 1/256, 1/512, 1/1024, 1/8192, 1/32768 of clock source frequency watchdog timer interrupt source 1/65536, 1/262144, 1/1048576 of system clock frequency dma controller (automatic data transfer) max. transfer cycles 255 starting factor e xternal request, various types of interrupt, software transfer mode 1-b yte transfer, word transfer, burst transfer serial interface serial 0 : synchronous type / uart (full-duplex) 1 clock source 1/2, 1/4 of system clock frequency; pulse output of timer counter 5; 1/2, 1/4, 1/16, 1/64 of osc oscillation clock frequency serial 1 : synchronous type / uart (full-duplex) 1 clock source 1/2, 1/4 of system clock frequency; pulse output of timer counter 4; 1/2, 1/4, 1/16, 1/64 of osc oscillation clock frequency serial 2 : synchronous type 1 clock source 1/2, 1/4 of system clock frequency; pulse output of timer counter 3; 1/2, 1/4, 1/16, 1/32 of osc oscillation clock frequency serial 3 : synchronous type/single-master i 2 c 1 clock source 1/2, 1/4 of system clock frequency; pulse output of timer counter 3; 1/2, 1/4, 1/16, 1/32 of osc oscillation clock frequency serial 4 : i 2 c slave 1 applicable for i 2 c high-speed transfer mode, 7 bit/10bit address setting, general call special ports buzzer output, remote control carrier signal output, high-current drive port a/d inputs 10-bit 7-ch. (with s/h) i/o pins 62 common use specified pull-up resistor available input/output selectable (bit unit) i/o 7 common use specified pull-up resistor available input see the next page for electrical characteristics, pin assignment and support tool. mad00036eem
pin assignment tqfp080-p-1212d * lead-free nc serves as the vpp pin in the mn101cf67g, and cannot be used as a user pin. MN101C67D mn101c67g electrical characteristics supply current limit symbol condition min typ max unit parameter idd1 fosc = 20 mhz, vdd = 3 v, (fs = fosc/2) 5 12 ma idd2 fosc = 8.39 mhz, vdd = 3 v, (fs = fosc/2) 2 5 ma idd3 fx = 32.768 khz, vdd = 3 v, (fs = fx/2) 40 a idd4 fx = 32.768 khz, vdd = 3 v, ta = 25 c48 a idd5 fx = 32.768 khz, vdd = 3 v 30 a idd6 vdd = 3 v, ta = 25 c2 a idd7 vdd = 3 v 20 a operating supply current supply current at halt supply current at stop ta = ? 40 c to +85 c, vdd = 1.8 v to 3.6 v, vss = 0 v 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 1 40 39 38 37 36 35 34 33 32 31 30 29 28 27 26 25 24 23 22 21 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 vref- an0/pa0 an1/pa1 an2/pa2 an3/pa3 an4/pa4 an5/pa5 outc nc vref+ vdd osc2 osc1 vss xi xo mmod txd1/sbo1/p00 sda/rxd1/sbi1/p01 scl/sbt1/p02 p34 p33 p32 sysclk/sbi3/p31 sbo3/p30 irq4/p24 irq3/p23 irq2/p22 acz/irq1/p21 irq0/p20 tcio7/p14 tcio3/p13 tcio2/p12 tcio1/p11 rmout/tcio0/p10 nrst/p27 ndk/buzzer/p06 sbt2/p05 sbi2/p04 sbo2/p03 p63/a3 p62/a2 p61/a1 p60/a0 p54/a17 p53/a16 p52/irq5/ncs p51/nre p50/nwe p47/key7/a15 p46/key6/a14 p45/key5/a9 p44/key4/a8 p43/tcio5/key3 p42/sbt0/key2 p41/rxd0/sbi0/key1 p40/txd0/sbo0/key0 p37/tcio4/ndkdma p36/sda p35/scl p64/a4 p65/a5 p66/a6 p67/a7 p70/sdo0 p71/sdo1 p72/a10/sdo2 p73/a11/sdo3 p74/a12/sdo4 p75/a13/sdo5 p76/sdo6 p77/sdo7 p87/led7,d7 p86/led6,d6 p85/led5,d5 p84/led4,d4 p83/led3,d3 p82/led2,d2 p81/led1,d1 p80/led0,d0 60 59 58 57 56 55 54 53 52 51 50 49 48 47 46 45 44 43 42 41 mad00036eem
support tool in-circuit emulator px-ice101c / d + px-prb101c67-tqfp080-p-1212-m flash memory built-in type MN101C67D, mn101c67g mad00036eem type mn101cf67g [es (engineering sample) available] rom ( 8-bit) 128 k ram ( 8-bit) 10 k minimum instruction execution time 0.1 s (at 3.0 v to 3.6 v, 20 mhz) package tqfp080-p-1212d *lead-free
request for your special attention and precautions in using the technical information and semiconductors described in this material (1) an export permit needs to be obtained from the competent authorities of the japanese government if any of the products or technical information described in this material and controlled under the "foreign exchange and foreign trade law" is to be exported or taken out of japan. (2) the technical information described in this material is limited to showing representative characteristics and applied circuits examples of the products. it neither warrants non-infringement of intellectual property right or any other rights owned by our company or a third party, nor grants any license. (3) we are not liable for the infringement of rights owned by a third party arising out of the use of the technical information as described in this material. (4) the products described in this material are intended to be used for standard applications or general electronic equipment (such as office equipment, communications equipment, measuring instruments and household appliances). consult our sales staff in advance for information on the following applications: ? special applications (such as for airplanes, aerospace, automobiles, traffic control equipment, combustion equipment, life support systems and safety devices) in which exceptional quality and reliability are re- quired, or if the failure or malfunction of the products may directly jeopardize life or harm the human body. ? any applications other than the standard applications intended. (5) the products and product specifications described in this material are subject to change without notice for modification and/or improvement. at the final stage of your design, purchasing, or use of the products, therefore, ask for the most up-to-date product standards in advance to make sure that the latest specifications satisfy your requirements. (6) when designing your equipment, comply with the guaranteed values, in particular those of maximum rating, the range of operating power supply voltage, and heat radiation characteristics. otherwise, we will not be liable for any defect which may arise later in your equipment. even when the products are used within the guaranteed values, take into the consideration of incidence of break down and failure mode, possible to occur to semiconductor products. measures on the systems such as redundant design, arresting the spread of fire or preventing glitch are recommended in order to prevent physi- cal injury, fire, social damages, for example, by using the products. (7) when using products for which damp-proof packing is required, observe the conditions (including shelf life and amount of time let standing of unsealed items) agreed upon when specification sheets are individually exchanged. (8) this material may be not reprinted or reproduced whether wholly or partially, without the prior written permission of matsushita electric industrial co., ltd. 2003 sep
|
